The WPN Series Bi-Metallic Steam Traps are used in steam tracing, steam main drips and non-critical process equipment. They can be used with superheated steam or on outdoor applications that are subject to freezing. The WPN Series Traps are available in multiple sizes and pressures up to 2,260 PSI.

SDM Series manifolds are used for steam distribution TO the tracing system and CCM Series for condensate collection FROM the tracing system. Commonly used in chemical and petrochemical facilities as well as in other industrial plants that have multiple tracing applications. Manifolding the steam distribution and condensate collection system not only cuts down on installation and maintenance costs, but also provides freeze protection. SDM Series manifolds come standard with integral, piston-style isolation valves; integral isolation valves are optional on CCM Series. FM Series manifolds are available in standard Fabricated Carbon Steel or Stainless Steel deigns, or can be custom built to meet specific application needs.

Referred to as radiator traps because the quick-disconnect pipe design is found on most radiators on 2-pipe steam heating systems. TA models have right angle discharge and the TS Type is straight-through. Their excellent air-handling capabilities and economical cost make them a great choice for air vents on heat exchangers or for steam trap applications on OEM equipment. Contains an extremely rugged precision-welded Stainless Steel thermal element which is highly resistant to waterhammer.

The Sump Drainer uses the same internal mechanism as the standard PMP models. The piping configuration is such that the liquid is discharged vertically out the top as opposed to horizontally out the side. This allows the unit to be easily positioned inside of a sump area. Condensate or water from the sump enters the tank through a stainless steel low resistance check valve. This unit is capable of operating with a maximum motive pressure of 150 PSIG using steam, air, nitrogen or other pressurized gas as the motive force.

Typically used in process applications for draining condensate from air for other gases. If a Float Type Liquid Drainer is selected, typically it is necessary to add a Balancing (or Equalizing) Line to allow any air or gases trapped in the drainer to escape. If the Balancing Line is not installed, these gases can prevent proper operation by air-binding the trap.

The WLD1800 and WLD1800R Drainers contain a stainless steel float and hardened stainless steel seat and disc to drain out liquids from pressurized piplines, tanks, and vessels without the loss of the pressured gas. Available in either a repairable (WLD1800R) or a non-repairable (WLD1800) version. The all stainless steel construction allows them to be used in extremely corrosive environments.

The E5600, E6600, and E7600 are high performance knife gate valves specifically designed for severe service type applications in the pulp & paper, mining, oil & gas, and power generation industries. Bidirectional, perimeter seat, transverse seal design WCB, stainless steel or high alloy body ASME Class 150 / 300 / 600 MSS SP-135 2” to 48” (larger on request)

The DBB5600, and DBB6600, are high performance, double block and bleed knife gate valves specifically designed for critical shut-off applications in the pulp & paper, mining, oil & gas, and power generation industries. Bidirectional, perimeter seat, transverse seal design Dual gate shut-off with a single actuator WCB, SS or high alloy body Class 150/300 MSS SP-152 2” to 24” (larger on request)

The OP5600 is a high performance, O-Port style knife gate valve specifically designed for use in severe service applications in the pulp & paper, chemical, mineral processing, and power generation industries. Through conduit, transverse seal design Stainless steel or high alloy body ASME Class 150 MSS SP-135 2” to 24” (larger on request)

The OP5700 is an O-Port style knife gate valve designed specifically for use in aggressive processes and high wear applications in the pulp & paper, and chemical industries. Through conduit design Hardened seat ring and gate ASME Class 150 MSS SP-135 2” to 24” (larger on request)

The E5500 knife gate valve is designed and configured specifically for use in industrial applications with high process temperatures. Up to 1200°F (650°C) max temperature Unidirectional resilient or metal seat Stainless steel or high alloy body ASME Class 150 MSS SP-135 2” to 12” (larger on request)

The E6300 knife gate valve is specifically designed for high pressures and heavy slurry use in the mining and mineral processing industries. Bidirectional, reinforced seat rings, push-through design WCB body Up to 750psi 3” to 24” (larger on request)

The E5300 knife gate valve is specifically designed for heavy slurry use in the mining and mineral processing industries. Bidirectional, reinforced seat rings, push-through design Ductile iron body Up to 150psi 2” to 24” (larger on request)

The E5800 knife gate valve is specifically designed for heavy slurry use in the mining and mineral processing industries. Wide body, flanged process connection Bidirectional, reinforced seat rings, push-through design Ductile iron body Up to 150psi 2” to 24” (larger on request)

The E5900 knife gate valve features a molded, high-quality urethane liner for use on erosive fine particle applications in mineral processing and other industries. Replaceable urethane seat cartridge Ductile iron body Up to 150psi MSS SP-81 2” to 24” (larger on request)